How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
We've unearthed this post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the internet and think it made sense to relate it with you in this article.
Mounting a bath tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is conveniently accessible, the job can relocate easily; if you have to open a wall to eliminate the old tub as well as position the new tub, the task is a lot harder. In either instance, the job is within a residence handyman's skills, although you will certainly require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified on your own for the work and also are comfortable attempting it. Rather than employing a specialist to take over a halfway-completed job, it is much better to consider employing one before you begin. Chances are you might require a specialist plumber to make tube links.
This article will certainly help you mount a brand-new bath tub in your bathroom if you have currently bought a brand-new bathtub and also do not require to alter the setup of your previous water supply pipes.
Your devices as well as material checklist ought to make up the following:
Preparing for the Installment
To start with, the sustaining framework supplied with the bath should be fitted (if called for) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the adaptable tap adapters to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be suited its last placement.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you should do is detach the water supply. After doing so, activate the taps to drain pipes any kind of water staying in the system. The procedure of eliminating the existing faucets can be rather bothersome because of the limited access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a towel ready for the staying water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any old securing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Utilizing both wooden boards under its feet, place the tub in the called for placement. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bath tub till the spirit level reads level.
To set up faucets, fit all-time low of the outermost adaptable faucet connector to the ideal supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Switch on the supply of water as well as inspect all joints as well as brand-new pipework for leaks and tighten them if required. Fill up the tub as well as likewise inspect the overflow electrical outlet as well as the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least when as this will certainly settle it into its final placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making certain that the washers are in place in between the faucet as well as the sink. Secure the tap in position with the producer provided backnut. Once the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet connectors. The previous type should be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bath and also the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and installations. They are sold in tubes as well as cartridges, and can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before securing, to allow for the movement experienced when the bathtub is in usage. The sealant can break rather early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently available on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof sticky and also grout.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/
I stumbled upon that blog post about How to Install a Bathtub Yourself while doing a lookup on the web. Liked our entry? Please share it. Let other people discover it. I am grateful for your time. Don't hesitate to come by our site back soon.
Request Your Service
Report this page